Goofy Grape

Vary the colors and shape details to make this project reflect your inner monster.

Products Used

  • CD-777 - Oval
  • S-2711 - Tahiti Grape
  • SC-13 - Grapel
  • SC-15 - Tuxedo
  • SC-16 - Cotton Tail
  • SC-74 - Hot Tamale
  • SC-76 - Cara-bein Blue
  • SP-253 - Speckled Purple Haze
Decorating Accessories
  • BT-910 - Synthetic Sponges
  • CB-106 - #6 Script Liner
  • CB-604 - #4 Soft Fan
  • CD-1078 - Design Press Tools
Additional Materials
  • Moist Clay
  • ¼" Wooden Slats
  • Canvas
  • Rolling Pin
  • Fettling Knife
  • Needle Tool
  • Slip/Clay Slurry
  • Straight Edge
  • Clay Extruder/Clay Gun
Project Info


  1. With a rolling pin on canvas, roll out a piece of moist clay ¼" thick between wooden slats.
  2. Stamp the slap with the triangle press tool from CD-780 before slumping the clay.
  3. Use the slump side of the CD-777 Oval to slump the shape for the head; two of these pieces are needed.
  4. When the clay pieces are firm enough so as not to loose their shape, slip attach the pieces together.
  5. Using a small slab for the bottom of the face, cut into the sides of the oval, cutting out about an inch from both seams in an oval shape. Score and brush with slip, then lay on the small slab piece. Cut around the shape to create a bottom. Blend the edges into the shape with your fingers.
  6. Pencil on an oval shape for the mouth opening which is off center. Roll some fat coils and lay them on the opening to create the shapes of lips. To make the lips protrude, attach a coil to the lower lip opening with a larger fat coil attached to the first coil.
  7. Cut out the opening of the mouth. Smooth out the opening with the lips, blending them together.
  8. Roll large balls of clay for the eyes and slip attach to the head. Roll smaller balls and press and roll in the star/asterick design from the CD-1078 Press Tool to form the shape attached to the large eyeball.
  9. Roll out a thinner piece of clay and cut out a shape for the tongue then slip attach to the inside of the mouth and turn up the end of the tongue.
  10. Form a piece of clay into a four fingered hand and arm. Attach to the back of the oval, bending it to bring it towards the lips, attaching the fingers to the face and lips as shown.
  11. For the hair use a small extruder/clay gun with the small holes attachment to make the spaghetti like hair. Attach with slip between the eyes.
  12. Allow to dry thoroughly.
  13. Bisque fire to shelf cone 04.

Painting Directions

  1. Using a CB-604 #4 Soft Fan, apply 3 coats of S-2711 Tahiti Grape on the head.
  2. Using a CB-106 #6 Script Liner, apply 3 coats of SC-74 Hot Tamale on the lips and tongue.
  3. Apply 3 coats of SP-253 Speckled Purple Haze on the hand and arm.
  4. Using a CB-106 #6 Script Liner, apply 3 coats of SC-16 Cotton Tail to the eyeball, then shade with thinned SC-76 Cara-bein Blue.
  5. Apply 3 coats of SP-253 Speckled Purple Haze to the iris of the eye, then shade the edges with SC-13 Grapel. Apply small circles of SC-15 Tuxedo in the center for the pupils.
  6. Shade around the lips and hands with SC-76 Cara-bein Blue, shading heavily at the top of the head around the hair and the spot where the eyes meet the head.
  7. Using a CB-604 #4 Soft Fan, apply some SP-253 Speckled Purple Haze and some SC-13 Grapel on the stringy hair. Apply to the inside of the mouth 2 heavy coats of SC-76 Cara-bein Blue.
  8. Stilt and fire to shelf cone 06.

Who We Are

Our purpose, history, and policies

About Us

Site Map

Warranty & Freeze Policy

Where To Buy

Find the best place to purchase Mayco products

Dealers & Retailers


PYOP & Ceramic Studios 

Contact Us

 (614) 876-1171 |   (614) 876-9904

Technical Support