• Mayco Designer Silkscreens are a great and easy way to add intricate detail to your work.
    Read More
  • Mayco Flux - SW-401 Light Flux & SW-402 Dark Flux Movement • Interaction • Beauty Mayco's SW-401 Light Flux and SW-402 Dark Flux
    Read More
  • 16 new stoneware glazes, including 6 soft mattes and 7 crystals. we also introduce a zinc-free clear that works well
    Read More
  • Convert your original artwork - or artwork for which you have the legal rights to use* - into a hand-applied silkscreen. No
    Read More
load more / hold SHIFT key to load all load all

Hand-BuiltSnail

Products Used

Material
  • 3lbs Low Fire 06/05 Clay (cone 05/06)
Color
  • SC-88 Tu Tu Tango
  • SC-97 Cant-elope
  • CG-966 Tiger Lily
  • S-2101 Crystal Clear Brushing

Decorating Accessories

  • CB-404 Pointed Round
  • CB-604 #4 Soft Fan
  • BT-910 Synthetic Sponge
  • CD777 Oval Slump & Hump Mold
  • XAR09 NamiWaves

Additional Materials

  • Pencil
  • 1/4" Wooden Slats
  • Canvas
  • Rolling Pin
  • Needle Tool
  • Slip or Clay Slurry
  • Ruler
  • Download: Pattern
 
Designer: Adena Griffith

Instructions

Hand-Building the Snail:

  1. Wedge a 3lb ball of low fire clay.
  2. Roll clay flat into a slab that is 3/8 if an inch thick.
  3. Choose an oval size for the body of the snail. Make 2 paper stencils of the oval you chose.
  4. Place the stencils on the slab and cut both ovals with a needle tool.
  5. Add texture by rolling XAR09 Xiem NamiWaves Art Roller over both ovals.
  6. Take a CD-777 Oval Slump & Hump mold and slump one of your textured ovals into the mold. Make sure the texture is facing down into the mold. Let this sit for 15-30mins and then repeat with other oval.
  7. Roll another slab and cut 3 long strips out of the slab that are 2-3 inches wide and long enough to go all the way around your slumped ovals.
  8. Attach one of the strips to one of the ovals and then attached the remanding oval to the other end of the strip. This will be the snails shell. Make sure you cut a small hole into the underside of the shell to keep it from blowing up in the kiln.
  9. With the other 2 long slabs, create the snail’s body. Attach the 1 slab to the underside of the snail. Leave a few inches in the back for the tail and the rest is for the head of the snail. Make sure you don’t close up the air vent that you created on the snail’s shell.
  10. Cut the end of the snail’s tail to a point.
  11. Take the other end of the slab and attach it to the shell to keep the head of the snail up.
  12. You have one half of the head of the snail done, but you need to use the 3rd for the other half of the head. You are creating a tube by attaching one part of the slab to the other.
  13. Close up the top of the tube and this will be the top of the snail’s head.
  14. Roll small coils and attach to the top of the head for the eyes.
  15. Let snail get to bone dry and fire to cone 04 to bisque.

Glazing Hand-Built Snail:

  1. Begin with properly fired shelf cone 04 bisque. Moisten a clean sponge and wipe bisque to remove any dust.
  2. Using CB-604 #4 Soft Fan brush apply 1 heavy coat of SC-97 Cant-elope to the textured part of the shell.
  3. Once that is dry take a damp BT-910 Synthetic Sponge and wipe away the
    SC-97 Cant-elope, leaving glaze in the texture part of the shell.
  4. When that is all dry apply 3 coats of CG-966 Tiger Lily to the shell of the snail. CG-966 Tiger Lilt is a translucent crystal glaze so the Cant-elope will show through the Tiger Lily.
  5. The body of the snail gets 3 coats of SC-88 Tu Tu Tango with a soft fan brush.
  6. While the third coat of SC-88 Tu Tu Tango is drying, float a coat of SC97 Cant-elope around the shell. Blend the 2 colors together.
  7. Fire to cone 06/05.

Who We Are

Our purpose, history, and policies

About Us

Site Map

Warranty & Freeze Policy

Where To Buy

Find the best place to purchase Mayco products

Dealers & Retailers

Distributors

PYOP & Ceramic Studios 

Contact Us

 (614) 876-1171 |   (614) 876-9904

info@maycocolors.com

Technical Support

614-675-2031

technical@maycocolors.com

Newsletter Sign-up